∏ PEI HU2100 ∟ 、‖。TPU D16N90UV、PC GS2040MR2、PP H2150、‖。PMMA 2014、‖。PP JM-350、‖。PBT B2300G6HRLS、‖。PC/ABS HP5008、‖。PP BX3910、‖。PC EXL1414、→，TPEE 440、‖。PA66 CR103、‖。PP MFB82I 、→，PP P60B08-S、PP 374NDCS1 、→，PEEK 2288LF、PA66 7520、LCP 7225、‖。PA66 A402、PA6 CM6241、→，PP PHIP-372、→，PP MVL36SX0、→，LCP 7145L 、‖。PMMA TS1785、‖。PP AT2717E、→，EVA 7A50H、EVA 250、PA66 KN333G30CRN、ABS VE-0812、LDPE LD103.59Film、PBT LPP0625-001

歡迎來電：15818465693（周生）0769-33214396? 可提供SGS,MSDS,COA,出廠認(rèn)證，

PEI is amorphous, and has outstanding high temperature resistance, high strength, high modulus and wide chemical resistance. It has natural flammability, low smoke emission and high lectric constant and dissipation factor.

Commodity name: ULTEM:

PEI plastic material in plastic online plastic Encyclopedia

The United States GE 1000-1000/71011010-1000/7001, ATX2002100220

Product introduction:

∏ PEI HU2100 ∟ PBT The rheological property of PET is better in the melting state, and the effect of pressure on the viscosity is larger than that of the temperature. Therefore, the flow of the melt is changed mainly from the pressure. 1, the treatment of plastics is due to the PET macromolecule containing lipid base, which has a certain hydrophilicity. The pellets are sensitive to water at high temperature. When the moisture content exceeds the limit, the molecular weight of PET decreases, and the products are colored and crisp. Therefore, it is necessary to dry the material before processing, and the drying temperature is 150, 4 hours, generally 170, 3-4 hours. The air - ejection method is used to test whether the material is completely dry. Generally, the proportion of the recycled material should not exceed 25%, and the recycled material should be completely dried.

2, PET is chosen for injection molding machine. Because of its short time after melting point and high melting point, it is necessary to choose injection system with more temperature control section and less friction heat when plasticizing, and the actual weight of products (water cut material) should not be less than 2/3 of machine injection volume. Based on these requirements, in recent years, Ramada has developed a small and medium-sized series of PET special plasticizing systems. The clamping force is selected by more than 6300t/m2.

3, mold and gate design, PET bottle embryo is usually molded by hot runner mold. Between the mold and injection molding machine template, it is best to he insulation panels, the thickness is about 12mm, and the heat insulation board will be able to withstand high pressure. The exhaust must be sufficient to oid partial overheating?or?fragmentation, but the depth of the exhaust port is generally not more than 0.03mm, otherwise it is easy to produce the fly edge.

Combustibility: it is difficult to burn and can continue to burn after fire.

Energy sing: the light transmittance is good, the light source products are reduced, electricity sing is sed, and the cost of use is reduced.

The shortcomings of PMMA are brittle and brittle, low surface hardness, easy to be scraped and lose luster, but fine scratches and scratches can be removed with polished paste. History

Acrylic (ACRYLIC), name of special treatment of organic glass. The research and development of acrylic has a history of more than 100 years ago. In 1872 of the polymerization of acrylic acid was found in 1880; methacrylate polymerization known; synthesis of poly propylene ester propionic acid in 1901; in 1927 using the synthesis method to industrialized manufacturing; 1937 methyl acid industrial manufacture was developed successfully, which entered the scale of manufacturing. In the course of World War II, acrylic has excellent toughness and light transmittance. First, it is applied to the windshield of the aircraft, and the perimeter of the tank driver's cab. In 1948, the first acrylic bathtub was born in the world, and then the application of acrylic entered a new milestone.

∏ PEI HU2100 ∟ 1. China's plexiglass and acrylic (acrylic) PMMA production and market situation. The total production capacity of China's plexiglass products is 130 thousand tons per day, and there are many manufacturers, but the scale of production is small.

China's organic glass acrylic production and processing capacity is very large, but the product structure is not very reasonable, it can only produce ordinary variety products, lack of high value-added products needed by construction industry, and can not meet the market demand in variety and quality, for example, the demand for building is very high

?