本公司長期供應貨源穩定，價格優惠，質量保證，歡迎來電咨詢
胡慶雄建議進行抗應激處理對因災減產的困難群眾給予必要幫助〖LCP V100P〗＝LCP Taking into account the service life of the screw, the temperature difference between the rear part, the middle part and the front part can be reduced. In order to prevent the nozzle salivation, nozzle temperature than shown in the table of the low temperature of 10 DEG C, if you want to improve the liquidity, the temperature can be shown in the table than the temperature higher than 20 DEG C, but must pay attention to the following circumstances.
Reduce the barrel temperature when the retention time is too long, will not cause the pellets in the barrel aging, does not produce corrosive gas, so long residence time is generally not what big problem. However, if the length of time to break down, please reduce the barrel temperature, once again, to throw away a few good.
The barrel temperature of each grade at molding (c)
B C Ei A
Posterior 250-290 280-340 300-360 250-290
Middle 270-290 300-340 310-350 270-290
Front 290-310 320-340 330-350 290-310
Nozzle 290-310 320-340 330-350 290-310
Resin temperature 290-320 320-350 340-360 290-320
2 mold temperature
LCP plastic raw material can be molded in a mold temperature of 30 degrees Celsius -150. But we generally set the mold temperature at 70 C -110 C. In order to shorten the molding cycle, preventing burr and deformation, should choose the low mold temperature; if the stable product size requirements (especially for products under high temperature conditions), reduce weld seam generating and solving the problem of insufficient filling, should choose the high mold temperature.
3 can be plastic
The rotating speed of the screw is generally 100rpm. If it is containing glass fiber or carbon fiber materials (such as: A130, A230, etc.), in order to prevent the glass fiber was broken, we must choose a relatively low speed. In addition, the back pressure is also as low as possible. When the barrel temperature is set to 300, the retention time of the material in the barrel has an effect on the mechanical properties and color of the plastic.
4 injection pressure and injection speed
The most appropriate injection pressure must depend on the shape of the material, the shape of the product, the design of the mold (especially for the straight runner, runner, gate) and other molding conditions. But no LCP grade the melt viscosity is very low, so the injection pressure than general thermoplastic resin to low. It is a good way to start with low pressure, and then slowly increase the pressure. Probably the products in 15MP
〈PA66 2411GF6〉 ‖PP HJ746‖╗ ABS⊙AF3009 BK∠ ‖PP TD211BF‖∫ ┿〔PC/ABS XCM840 〕 賣〈TPU B85A11〉現貨 PP“RJ170MO╬ ≮〔LCP E135i 〕 ABS⊙GSM╯ ‖TPU 58863‖【 〈COC E48〉 PA66↓RFL36XX GY¨ 〈PA66 26FE7〉 PMMA～8NDF23ぁ →〔EVA 40-55〕 〈PET PT4232〉 ‖PP P740J‖① PBT←1494X02－ ‖EVA EV101‖╡ POM●M90CA▆?? PA6♂1011GH5∞ ‖PP C342M6‖∩ ‖PC/ABS 9000‖▄ 賣〈TPU T785〉（圖） PA66↓LUBRILOY R∧