亚洲日韩小电影在线观看_无码欧精品亚洲日韩一区_吸咬奶头狂揉60分钟视频_久久久婷婷五月亚洲97号色

東莞市廣豐聯泰塑料有限公司

專供PC+ABS 沙伯基礎PC 德國拜耳PC+ABS 寶理PPS LCP

產品分類
聯系方式
友情鏈接
您當前的位置：首頁 » 新聞中心 » PBT+PET VALOX 855 應用程序:外部外殼,蒸汽熨斗、家電外殼和照明部分。
新聞中心
PBT+PET VALOX 855 應用程序:外部外殼,蒸汽熨斗、家電外殼和照明部分。
發布時間：2016-04-14        瀏覽次數：348        返回列表
VALOX 855玻璃增強PBT+PET 15% 提高表面的外觀。應用程序:外部外殼,蒸汽熨斗、家電外殼和照明部分。

Sabic沙伯基礎創新塑料:PBT 855、865、DR48、DR48 - CS1049、DR51、ENH3500、ENH4530、ENH4550、ENH4560、ENH4565、HX312C、HX420HP、K3501、K4530、K4560、SHF4910、SHF4930、SHF4960、V2000DM、V3500EX、V4860HR、VX4920、VX4930、VX5011、VX5022、

 

VALOX ? Resin 855

SI | British | Metric | PDF Europe-Africa-Middle East: COMMERCIAL

 
VALOX 855 is 15% glass reinforced PBT+PET blend with improved surface appearance. Applications: external housings, steam irons, appliance housings and lighting parts.
 

Property
 
TYPICAL PROPERTIES (1)
MECHANICAL Value Unit Standard
Tensile Stress, yld, Type I, 5 mm/min 1010 kgf/cm2 ASTM D 638
Tensile Stress, brk, Type I, 5 mm/min 1010 kgf/cm2 ASTM D 638
Tensile Strain, yld, Type I, 5 mm/min 2 % ASTM D 638
Tensile Strain, brk, Type I, 5 mm/min 3 % ASTM D 638
Tensile Modulus, 5 mm/min 66200 kgf/cm2 ASTM D 638
Flexural Stress, yld, 1.3 mm/min, 50 mm span 1500 kgf/cm2 ASTM D 790
Flexural Stress, brk, 1.3 mm/min, 50 mm span 1500 kgf/cm2 ASTM D 790
Flexural Modulus, 1.3 mm/min, 50 mm span 53000 kgf/cm2 ASTM D 790
Taber Abrasion, CS-17, 1 kg 17 mg/1000cy SABIC Method
Tensile Stress, yield, 5 mm/min 100 MPa ISO 527
Tensile Stress, break, 5 mm/min 100 MPa ISO 527
Tensile Strain, yield, 5 mm/min 2 % ISO 527
Tensile Strain, break, 5 mm/min 3 % ISO 527
Tensile Modulus, 1 mm/min 6500 MPa ISO 527
Flexural Stress, yield, 2 mm/min 150 MPa ISO 178
Flexural Stress, break, 2 mm/min 150 MPa ISO 178
Flexural Strain, break, 2 mm/min 3 % ISO 178
Flexural Modulus, 2 mm/min 5400 MPa ISO 178
Hardness, H358/30 126 MPa ISO 2039-1
Hardness, Rockwell R 120 - ISO 2039-2
IMPACT Value Unit Standard
Charpy Impact, unnotched, 23°C 25 kJ/m2 ISO 179/2C
Charpy Impact, unnotched, -30°C 25 kJ/m2 ISO 179/2C
Izod Impact, unnotched, 23°C 40 cm-kgf/cm ASTM D 4812
Izod Impact, unnotched, -30°C 40 cm-kgf/cm ASTM D 4812
Izod Impact, notched, 23°C 5 cm-kgf/cm ASTM D 256
Izod Impact, notched, 0°C 5 cm-kgf/cm ASTM D 256
Izod Impact, notched, -30°C 5 cm-kgf/cm ASTM D 256
Instrumented Impact Total Energy, 23°C 61 cm-kgf ASTM D 3763
Izod Impact, unnotched 80*10*4 +23°C 25 kJ/m2 ISO 180/1U
Izod Impact, unnotched 80*10*4 -30°C 23 kJ/m2 ISO 180/1U
Izod Impact, notched 80*10*4 +23°C 6 kJ/m2 ISO 180/1A
Izod Impact, notched 80*10*4 0°C 6 kJ/m2 ISO 180/1A
Izod Impact, notched 80*10*4 -30°C 6 kJ/m2 ISO 180/1A
Charpy 23°C, V-notch Edgew 80*10*4 sp=62mm 8 kJ/m2 ISO 179/1eA
Charpy Impact, notched, 23°C 6 kJ/m2 ISO 179/2C
Charpy -30°C, V-notch Edgew 80*10*4 sp=62mm 4 kJ/m2 ISO 179/1eA
Charpy Impact, notched, -30°C 6 kJ/m2 ISO 179/2C
Charpy 23°C, Unnotch Edgew 80*10*4 sp=62mm 20 kJ/m2 ISO 179/1eU
Charpy -30°C, Unnotch Edgew 80*10*4 sp=62mm 15 kJ/m2 ISO 179/1eU
THERMAL Value Unit Standard
Vicat Softening Temp, Rate A/50 217 °C ASTM D 1525
Vicat Softening Temp, Rate B/50 196 °C ASTM D 1525
HDT, 0.45 MPa, 3.2 mm, unannealed 215 °C ASTM D 648
HDT, 1.82 MPa, 3.2mm, unannealed 187 °C ASTM D 648
CTE, -40°C to 40°C, flow 3.E-05 1/°C ASTM E 831
CTE, -40°C to 40°C, xflow 7.4E-05 1/°C ASTM E 831
CTE, -20°C to 150°C, flow 2.7E-05 1/°C ASTM E 831
CTE, -20°C to 150°C, xflow 1.7E-04 1/°C ASTM E 831
Thermal Conductivity 0.19 W/m-°C ISO 8302
CTE, -40°C to 40°C, flow 2.95E-05 1/°C ISO 11359-2
CTE, -40°C to 40°C, xflow 7.42E-05 1/°C ISO 11359-2
CTE, 23°C to 150°C, flow 2.74E-05 1/°C ISO 11359-2
CTE, 23°C to 150°C, xflow 1.74E-04 1/°C ISO 11359-2
Ball Pressure Test, 125°C +/- 2°C PASSES - IEC 60695-10-2
Vicat Softening Temp, Rate A/50 217 °C ISO 306
Vicat Softening Temp, Rate B/50 196 °C ISO 306
Vicat Softening Temp, Rate B/120 196 °C ISO 306
HDT/Be, 0.45MPa Edgew 120*10*4 sp=100mm 210 °C ISO 75/Be
HDT/Ae, 1.8 MPa Edgew 120*10*4 sp=100mm 175 °C ISO 75/Ae
HDT/Bf, 0.45 MPa Flatw 80*10*4 sp=64mm 215 °C ISO 75/Bf
HDT/Af, 1.8 MPa Flatw 80*10*4 sp=64mm 185 °C ISO 75/Af
Relative Temp Index, Elec 125 °C UL 746B
Relative Temp Index, Mech w/impact 110 °C UL 746B
Relative Temp Index, Mech w/o impact 125 °C UL 746B
PHYSICAL Value Unit Standard
Specific Gravity 1.5 - ASTM D 792
Filler Content 15 % ASTM D 229
Mold Shrinkage on Tensile Bar, flow (2) (5) 0.4 - 0.8 % SABIC Method
Mold Shrinkage, flow, 3.2 mm (5) 0.6 % SABIC Method
Mold Shrinkage on Tensile Bar, xflow (2) (5) 0.6 - 1 % SABIC Method
Melt Flow Rate, 266°C/5.0 kgf 79 g/10 min ASTM D 1238
Density 1.5 g/cm3 ISO 1183
Water Absorption, (23°C/sat) 0.45 % ISO 62
Moisture Absorption (23°C / 50% RH) 0.06 % ISO 62
Melt Volume Rate, MVR at 250°C/5.0 kg 32 cm3/10 min ISO 1133
Melt Volume Rate, MVR at 265°C/1.2 kg 11 cm3/10 min ISO 1133
Melt Volume Rate, MVR at 265°C/5.0 kg 60 cm3/10 min ISO 1133
Melt Viscosity, 260°C, 1500 sec-1 135 Pa-s ISO 11443
ELECTRICAL Value Unit Standard
Volume Resistivity 1.E+15 Ohm-cm ASTM D 257
Dielectric Strength, in oil, 0.8 mm 33 kV/mm ASTM D 149
Dielectric Strength, in oil, 1.6 mm 25 kV/mm ASTM D 149
Dielectric Strength, in oil, 3.2 mm 18 kV/mm ASTM D 149
Relative Permittivity, 100 Hz 3.5 - ASTM D 150
Relative Permittivity, 1 MHz 3.3 - ASTM D 150
Dissipation Factor, 100 Hz 0.001 - ASTM D 150
Dissipation Factor, 1 MHz 0.015 - ASTM D 150
Arc Resistance, Tungsten {PLC} 6 PLC Code ASTM D 495
Hot Wire Ignition {PLC) 0 PLC Code UL 746A
High Voltage Arc Track Rate {PLC} 4 PLC Code UL 746A
High Ampere Arc Ign, surface {PLC} 4 PLC Code UL 746A
Comparative Tracking Index (UL) {PLC} 3 PLC Code UL 746A
Volume Resistivity 1.E+15 Ohm-cm IEC 60093
Surface Resistivity, ROA >1.E+15 Ohm IEC 60093
Dielectric Strength, shorttime, 1.0mm 21 kV/mm IEC 60243-1
Dielectric Strength, in oil, 0.8 mm 33 kV/mm IEC 60243-1
Dielectric Strength, in oil, 1.6 mm 25 kV/mm IEC 60243-1
Dielectric Strength, in oil, 3.2 mm 18 kV/mm IEC 60243-1
Relative Permittivity, 100 Hz 3.5 - IEC 60250
Relative Permittivity, 1 MHz 3.3 - IEC 60250
Dissipation Factor, 50/60 Hz 0.001 - IEC 60250
Dissipation Factor, 100 Hz 0.001 - IEC 60250
Dissipation Factor, 1 MHz 0.01 - IEC 60250
Comparative Tracking Index 225 V IEC 60112
Comparative Tracking Index, M 175 V IEC 60112
Relative Permittivity, 50/60 Hz 3.3 - IEC 60250
FLAME CHARACTERISTICS Value Unit Standard
UL Recognized, 94V-0 Flame Class Rating (3) 1.5 mm UL 94
Glow Wire Flammability Index 960°C, passes at 1 mm IEC 60695-2-12
Oxygen Index (LOI) 27 % ISO 4589
Source GMD, last updated:2012/12/19
Processing

Parameter
Injection Molding Value Unit
Drying Temperature 110 - 120 °C
Drying Time 4 - 6 hrs
Maximum Moisture Content 0.02 %
Melt Temperature 260 - 285 °C
Nozzle Temperature 265 - 275 °C
Front - Zone 3 Temperature 260 - 280 °C
Middle - Zone 2 Temperature 255 - 280 °C
Rear - Zone 1 Temperature 240 - 260 °C
Hopper Temperature 40 - 60 °C
Mold Temperature 60 - 110 °C
Source GMD, last updated:2012/12/19

轉載請注明：轉載自環球塑化資訊網 http://www.j165.com/news/
本文鏈接：http://www.j165.com/b-shabo/news269048/
免責聲明：本文"PBT+PET VALOX 855 應用程序:外部外殼,蒸汽熨斗、家電外殼和照明部分。"僅代表作者個人觀點，與環球塑化網無關。環球塑化網所轉載的內容，其版權均由原作者和資料提供方所擁有！如因作品版權問題需要處理，請與我們聯絡。電話：400-115-2868

機械手 激光機
©2025 環球塑化網 版權所有   技術支持： 環球塑化網     訪問量：626022  管理入口

收縮

  • 電話咨詢

  • 0769-82558310
QR code
關閉
關閉
請輸入驗證碼
主站蜘蛛池模板： 安国市| 商洛市| 上饶市| 潞西市| 洛扎县| 齐河县| 扎囊县| 威海市| 龙南县| 两当县| 防城港市| 雷州市| 尉犁县| 霞浦县| 宣武区| 楚雄市| 昭通市| 静安区| 栾川县| 常山县| 普安县| 泽州县| 改则县| 怀远县| 古浪县| 林州市| 霍林郭勒市| 清徐县| 清河县| 遂昌县| 福清市| 兴城市| 许昌县| 绥芬河市| 和田县| 霞浦县| 江安县| 离岛区| 英吉沙县| 铁力市| 汝州市|